Predicting Folds in Fiberglass Fabrics During Draping

»FoldPrediction« Project of the German Research Foundation (DFG): Model-Based Prediction of Crease Formation in Textile Composite Reinforcements

As part of the DFG project »FoldPrediction«, we collaborated with the Institut für Textiltechnik of RWTH Aachen University to investigate when glass fiber fabrics form folds as they conform to three-dimensional shapes. The team combined material testing with digital textile models and simulations. The results make it possible to better estimate the location, size, and shape of folds and to plan draping processes more precisely.

Fiberglass fabrics serve as reinforcing inserts in plastic components and are used primarily in the automotive and aerospace industries. During draping, the flat fabric is conformed to a three-dimensional mold. As this happens, the fiber bundles – known as  »Rovings« – slide at points of contact and shift relative to one another. This causes folds to form. These folds can significantly compromise the quality and strength of the final component.

The project investigated various glass fiber fabrics with different weave types and weights per unit area. The researchers documented how tensile behavior, bending, friction, and the relative displacement of the rovings contribute to the formation of folds. Under shear load, the angle between the warp and weft yarns changes. This angle reaches a critical value at which shear is blocked – resulting in unwanted folds during draping. This is a crucial process in draping.

SEM image of a selected glass fiber fabric in plan view
© Institut für Textiltechnik of RWTH Aachen University
SEM image of a selected glass fiber fabric in plan view
SEM image of a selected glass fiber fabric in plan view
© Institut für Textiltechnik of RWTH Aachen University
SEM image of a selected glass fiber fabric in plan view

Digitally Modeling Glass Fiber Fabrics and Simulating Shear Behavior

For the various fabric types, the team determined the geometry and tensile behavior of individual rovings. It also measured how the fabrics respond to bending and shearing and how the cross-sections of the rovings change as a result.

At Fraunhofer ITWM, we converted this data into digital representations of the fabrics in our TexMathsoftware. These digital twins represent the fabric structure, the properties of the rovings, and their friction at contact points. From a representative section of fabric, the team derived values that describe the tensile, bending, and shear behavior of the entire textile. After comparison with measurement data, the simulations reproduced the measured shear stress curves within the experimental range.

Shear frame test to determine the shear stiffness of the investigated glass fiber fabrics. The experimental results serve as a basis for comparison with the simulations.
© Institut für Textiltechnik of RWTH Aachen University
Shear frame test to determine the shear stiffness of the investigated glass fiber fabrics. The experimental results serve as a basis for comparison with the simulations
Force–strain behavior of individual rovings as input parameters for the simulation of glass fiber fabrics
© Fraunhofer ITWM
Force–strain behavior of individual rovings as input parameters for the simulation of glass fiber fabrics
Vergleich von Simulation und Experiment am Beispiel der Schubsteifigkeit eines Glasfasergewebe
© Fraunhofer ITWM
Vergleich von Simulation und Experiment am Beispiel der Schubsteifigkeit eines Glasfasergewebes: Die grüne Linie zeigt den punktweisen Mittelwert der Messungen, der graue Bereich deren Standardabweichung und die blaue Linie das Simulationsergebnis.

Measuring Pleat Geometry in Three-Dimensional Glass Fiber Fabrics

For the experiments, our researchers draped square fabric samples over a doubly curved, spherical mold. A robot performed the shaping, and a vacuum held the fabric in place. A 3D laser scanner then captured the surface of the shaped fabric. The data describe the geometry of the folds and show how closely the fabric matches the desired shape and intended dimensions.

The researchers compared the measured folds of lighter and heavier fabrics with the simulations. Systematic comparative calculations show that friction between the rovings and the orientation of the fabric cut relative to the two thread directions strongly influence the fold pattern.

Spherical tool shape for draping experiments to investigate wrinkle formation in glass fiber fabrics
© Institut für Textiltechnik of RWTH Aachen University
Spherical tool shape for draping experiments to investigate wrinkle formation in glass fiber fabrics
Faltenbildung im Vergleich
© Fraunhofer ITWM
Faltenbildung im Vergleich: Experimentelle Aufnahmen der drapierten Glasfasergewebe (links) und die entsprechenden Simulationsergebnisse (rechts).
Einfluss der Auflösung des Finite-Elemente-Netzes auf die simulierte Faltenbildung
© Fraunhofer ITWM
Einfluss der Auflösung des Finite-Elemente-Netzes auf die simulierte Faltenbildung: Die Darstellung zeigt die Faltenentwicklung bei zunehmender Verfeinerung des Berechnungsnetzes.

Targeted Planning of Layup Processes for Fiber-Reinforced Composite Parts

The results provide a basis for more targeted planning of layup processes. They support the selection of fabric structure and fiber orientation and help to avoid problematic creases as much as possible – or to place them strategically – by adjusting the mold shape.

Project Funding and Duration

The DFG project »FoldPrediction – Model-Based Prediction of Fold Formation in Textile Composite Reinforcements« was funded by the German Research Foundation DFG  (»Deutsche Forschungsgemeinschaft«) from 2022 to 2026. The goal of the project was to better understand the formation of folds in glass fiber reinforcement fabrics during the forming process into three-dimensional components and to predict this behavior using simulations. The findings support the development of robust and quality-assured manufacturing processes for fiber-reinforced composites.

Experimental Setup at ITA: A robot presses the positive tool mold into the textile sample
© Institut für Textiltechnik of RWTH Aachen University
Experimental Setup at ITA: A robot presses the positive tool mold into the textile sample